Parting and Grooving Inserts ERMN Profile Grooving

Looking for high-quality ERMN profile grooving inserts? Look no further than our factory! We offer top-notch parting and grooving inserts for your machining needs.

Request a Quote
  • Parting and Grooving Inserts ERMN Profile Grooving

PRODUCTS DETAILS

High surface finish factor, good abrasion resistance. High precision, new coating technology. Adopt imported technology to process, the overall hardness is stronger, and the service life of the blade is longer.

Type

Fn

(mm/rev)

Grade

CVD

PVD

VK4215

VK4225

VK4235

VK4315

VK4325

VK1025

VK1824

VK1825

VK1528

VR1010

VR1525

ERMN300-T

0.05-0.18

O

ERMN400-T

0.07-0.25

O

ERMN500-T

0.08-0.3

O

ERMN600-T

0.09-0.35

O

• : Recommended Grade O: Optional Grade

Width

Size(mm)

S

r±0.1

L

300

3.0

1.5

21.1

400

4.0

2

26.4

500

5.0

2.5

27.2

600

6.0

3

27.5

11. Flank Wear? Higher cutting resistance,Notch wear on flank, Poor roughness of surface, or deterioration of accuracy. Soft grades,Excessive cutting speed,Small flank angle,Low feed. Select a higher,wear-resistant grade,Reduce cutting speed,Increase flank angle,Increase feed. 2. Crater Wear? Uncontrolled chip,Poor surface quality,when finishing High speed processing carbon steel. Soft grades,Excessive cutting speed, Excessive feed,The strength of chip breaker Insufficient. Change to a higher wear-resistant grade,Reduce cutting speed,Reduce feed, Select a higher strength chip breaker. 3. Chipping? Sudden fracture of cutting edge(rake face and flank),Instability insert life. Toughness insufficient,Excessive feed rate,Strength of cutting edge insufficient,Instability of the tool. Select a tougher grade, Decrease feed rate, Increase honing of cutting edge(chamfering to rounding),Increase the stability and setting angle. 4. Insert Fracture? Cutting resistance increased Poor surface roughness. Toughness insufficient, Excessive feed rate, Strength of cutting edge insufficient,Instability of the tool. Select a tougher grade, Decrease feed rate,Increase honing of cutting edge(chamfering to rounding),Increase the stability and setting angle. 5. Plastic Deformation? Variation of dimension Nose wear,cutting edge drape or passivating.when processing alloy steel Poor surface roughness. Soft grade,Excessive cutting speed,Excessive cutting depth and feed rate,Overheat on cutting edge. Select a higher red hardness cutting material,Decrease cutting speed,Decrease cutting depth and feed rate,Select a higher thermal conductivity cutting material(CVD+sufficient coolant). 6. Build-Up-Edge? Workpiece dissolve with Cutting edge Poor surface roughness when finishing,Cutting resistance increased,Cutting soft materials. Cutting speed too low, Cutting edge obtuse,Unsuitable tool material. Increase cutting speed, Increase rake angle,Select small sticking force.When a cutting edge becomes dull, you just need to rotate the insert in the holder to use the sharp edge. It is coated, providing much longer tool life than uncoated inserts.

Hot Products

Carbide Flat End Mills

Carbide Flat End Mills

High Feed Milling Insert LOGU Carbide Inserts

High Feed Milling Insert LOGU Carbide Inserts

Profile Milling Insert RPKT Carbide Inserts

Profile Milling Insert RPKT Carbide Inserts

High Feed Milling Insert LNMU Carbide Insert

High Feed Milling Insert LNMU Carbide Insert

Tungsten Carbide Heading Dies

Tungsten Carbide Heading Dies

General Turning Inserts WNMG Carbide Insert

General Turning Inserts WNMG Carbide Insert

Profile Milling Insert RPMT Carbide Insert

Profile Milling Insert RPMT Carbide Insert

Parting and Grooving Inserts ECMN Parting And Grooving

Parting and Grooving Inserts ECMN Parting And Grooving

Face Milling Inserts SEMT Carbide Insert

Face Milling Inserts SEMT Carbide Insert

Longneck End Mills

Longneck End Mills

Contact us

Please feel free to give your inquiry in the form below We will reply you in 24 hours